<form id="9nhij"><legend id="9nhij"></legend></form>
    1. <strike id="9nhij"></strike>
        1. <sub id="9nhij"><table id="9nhij"><small id="9nhij"></small></table></sub>

          Se Habla Espa?ol

          Servicing the Hydraulic Rebuilding Industry

          Email: sales@ms-d.com
          En Espa?ol: luis@ms-d.com

          What's New

          Our Heavy Duty cylinder disassembly/assembly table and tooling designed for cylinders up to 24 to 30 inches in diameter. The table is designed with the top rail modified from 3/4" to 1-1/4" steel and is 26.5 ft. Long. A cylinder assist for disassembly and re assembly, a 24" heavy duty triple chain vise, a pressure boost system and 70K Nut Buster have been developed in conjunction with the heavy duty disassembly table.

          Download an informational brochure on the Disassembly Bench Model MSD-D-HD26

          We accept:

          Hydraulic Cylinder Disassembly Table

          hydraulic cylinder table disassembly fixture

          Cylinder Table – Disassembly Fixture

          Cylinder repair begins on the cylinder disassembly table. Selecting the proper cylinder repair equipment is critical to the success and ease of operation.

          The Disassembly Fixture incorporates these features:

          • A sturdy 2” x 4” tubular frame
          • 15-, 20-, 25- and 30-ft. standard table lengths (can be made to any length)
          • Full-length collector pan
          • 40 gal. drain pan
          • Two (2) slide plates

          MSD-D-15 | 15-ft Disassembly Fixture
          MSD-D-20 | 20-ft Disassembly Fixture
          MSD-D-25 | 25-ft Disassembly Fixture
          MSD-D-30 | 30-ft Disassembly Fixture

          Disassembly Machine Spec Sheet

          Collector Pan & 40 Gal. Drain Pan

          collector pan for hydraulic cylinder repair bench 40-gallon drain pan for cylinder bench

          The full length large volume collector pan helps keep your shop clean and promotes safety by eliminating oil spillage while disassembling components.

          A 40-gallon drain pan, supported on a section of roller conveyor, rolls out for easy disposal of waste oil. This tank is also used to capture oil from an overhung cylinder head during disassembly. The pan is rolled back after use thus eliminating a safety hazard and maintaining a clean and dry working area.

          Slide Plates

          slide plate with predrilled holes for hydraulic cylinder disassembly table

          Each Disassembly table comes with two (2) slide plates. They consist of 32” x 12” x ?” pre drilled plates. The predrilled holes will accept standard 8” chain vises, tie-bolt cylinder hold down clamps and brace tooling. There is also a 1” hole on either side of the plates located in the center for mounting a cylinder for the pull-apart assembly. Each slide plate comes with two (2) “L” clamps to lock it to the main table. The slide plates can be easily and quickly moved to the desirable position then locked down by tightening the clamps. There are also predrilled holes that allow you to pin the plates for positive locking at 10” increments along the full length of the fixture.


          disassembly table configured to pull apart hydraulic cylinder

          Cylinders that have dented tubes or bent shafts can be pulled apart with the configuration shown. Brace tool “A” after being secured to a slide plate is pinned to make it stationary. Hydraulic cylinder “C” is positioned between the stationary plate “B” and a second brace tool “D” mounted on a sliding plate. When the cylinder is extended a lineal force is generated to separate parts.

          Tie-bolt cylinders can be secured to slide plates using pre-drilled holes and simple hold down tooling (MSD-HD). The slide plates insure a secure parallel surface for assembly and/or removal of tie bolt rods.

          Integrated Power Unit Option

          The standard MS&D Disassembly Table has the option of a built-in power unit. The power unit consists of a 40?gallon reservoir, 15hp. 3 phase motor and starter, a 2 stage gear pump that will develop 15 gpm and 3500psi. This power unit can be used to power the “Nut Buster” and pressure test cylinders being repaired. Single phase motors and smaller motor/pump combinations are options. A 100-gallon reservoir is available.

          Disassembly Table shown with Hitachi 1800 Boom Cylinder rod.

          disassembly table with optional built-in power unit shown with Hitachi 1800 Boom Cylinder rod and technician

          Integrated Power Unit and Control Panel.

          Air Purge & Control Panel

          air purge system control panel for hydraulic cylinder disassembly table

          An air purge system is incorporated into the unit to purge oil from cylinders after testing.

          The control panel has a main pressure gauge with indicator needle (this registers the pressure the nut broke loose and will quantify the torque at which it will be tightened) for operation of the Nut Buster?. The cylinder test portion of the panel contains a two-spool control valve, two work port pressure gauges, adjustable relief valve and isolation valves to check leakage across pistons.

          Nut Buster? Option

          Nut Buster hydraulic wrench option for disassembly bench

          Our "Nut Buster” hydraulic wrench can develop high torque at standard hydraulic pressures. Standard sizes of our “Nut Buster” develop 20, 30, 40 and 50,000 ft./lbs of torque. A simple and rugged system incorporates two (2) opposing cylinders working with a ratcheting mechanism. As the cylinders extend they rotate the “tool holder” 60 deg. The cylinders retract and the cycle is repeated until the nut or head is completely removed.

          The MS&D Torque fixture accepts a simple 8” x 8” square plate as tooling. The plate is placed in the 8” x 8” cavity on either end of the fixture. A 45? turn of the tool captures the tool in place. A hex hole up to 6” is made for the larger nuts. Various other whole shapes can be made to remove almost any type of nut, head, or glands on shafts or cylinder tubes.

          MSD-PBS | Pressure Boost System

          An option for the disassembly table power unit, the Pressure Boost System consists of an air-opreated pump with a safety relief valve integrated into the standard power unit to boost the system pressure to 6000 psi. A manifold block isolates the boost pressure from the main system.

          Heavy Duty Disassembly Fixture - MSD-D-HD26

          heavy-duty hydraulic cylinder disassembly & repair bench

          The Heavy Duty Disassembly / Assembly bench incorporates these features:

          • 26.5 feet long and reinforced in the lower section
          • Top rail is modified from ?” to 1-1/4” steel
          • Full-length collector pan
          • One 40-gal. Drain pan
          • Also available in 38 foot and custom lengths
          • View or download MSD-D-HD26 brochure PDF

          Click For Heavy Duty Tooling

          MSD-D-15E | 15-ft Economy Disassembly Table
          MSD-D-20E | 20-ft Economy Disassembly Table
          MSD-D-25E | 25-ft Economy Disassembly Table

          These Economy Disassembly Tables are an affordable alternative to our standard Disassembly Table. The table is manufactured without the collector pan, and the slide rails are not predrilled. The pullout drain pan with roller conveyor and slide plates are not supplied but can be added as an option. The work station accommodates all of our existing tooling and fixtures.

          economy hydraulic cylinder bench